Tv Antenna Installation Melbourne Vic 

 

TV antenna installation typically starts from $220, depending on the type of antenna and any additional equipment required to ensure a strong and reliable signal.

Antenna installations can start from $180, while a single TV wall point installation starts from $150. Final pricing may vary based on the complexity and duration of the job.

Labour rates generally range between $90 and $100 per hour.

 

TV Reception, TV Points & Wall Mounting Services

Our experienced antenna and TV reception specialists offer a full range of reliable home entertainment services, including:

  • Additional TV point installation for convenient viewing in multiple rooms
  • Antenna and reception fault diagnosis and repair service calls
  • Professional TV wall mounting (“hanging TV”) services
  • Signal testing, tuning, and optimisation for clearer picture quality
  • And a variety of other customised TV and antenna solutions

Whether you’re expanding your home setup or troubleshooting reception issues, our team ensures a fast, tidy, and professional result every time.

 

TV Antenna Services

Installing or repairing a TV antenna isn’t just about putting equipment on a roof — it’s about ensuring your system is set up for the best possible reception and long-term reliability.

A professional TV antenna installation service provides the following:

  • Correct antenna selection based on your location and signal strength
  • Safe, secure roof installation
  • Neat and durable cable routing using quality materials
  • Reduced signal interference and fewer picture dropouts
  • Access to a wider range of free-to-air digital channels
  • Improved HD and 4K picture quality
  • Full testing and tuning for optimal reception
  • Repairs and upgrades for damaged or outdated systems

Whether you’re installing a new antenna or repairing an existing setup, a qualified technician ensures everything is properly fitted, fully tested, and ready for consistent, high-quality viewing.

 

1. Choose the right antenna type

In Australia, most homes use a UHF/VHF rooftop antenna for free-to-air TV.

  • UHF antennas: Most common in metro areas like Melbourne
  • VHF antennas: Sometimes needed in regional zones
  • Combo (VHF + UHF): Safest choice if unsure

If reception is already weak in your area, a higher-gain directional antenna is usually needed.

2. Find the best location

Signal quality depends heavily on placement.

  • Highest point on the roof (best signal)
  • Clear line of sight toward broadcast towers (in Melbourne, often Mt Dandenong)
  • Avoid obstruction from:
    • Trees
    • Nearby buildings
    • Metal roofs or foil insulation barriers

A small change in position can dramatically improve signal strength.

3. Mount the antenna securely

You’ll typically mount it on:

  • Roof ridge
  • Chimney bracket
  • Wall/eave mast

Make sure:

  • The mast is vertical (use a spirit level)
  • All bolts are tightened
  • It is wind-resistant (important in Melbourne storms)

4. Align the antenna

This is the most critical step.

  • Point it toward the nearest transmission tower (in Melbourne: usually Mount Dandenong
  • Use a compass app or signal finder tool
  • Slight adjustments (5–10°) can make a big difference

Have someone monitor TV signal strength while you adjust if possible.

5. Run the coaxial cable

  • Use RG6 coax cable (standard for TV)
  • Keep cable runs as short as practical
  • Avoid sharp bends or crushing the cable
  • Seal outdoor connectors with weatherproof tape or gel

If going through the roof cavity, secure cable to joists to avoid movement damage.

6. Connect to TV and test

  • Plug cable into the TV or set-top box
  • Run auto channel scan
  • Check for pixelation or dropouts
  • Fine-tune antenna direction if needed

7. Optional: use a signal amplifier

Only use an amplifier if:

  • Signal is weak after correct alignment
  • Long cable runs reduce quality

Too much amplification can actually worsen reception, so don’t add it unless necessary.

Safety notes

  • Avoid working on roofs in wet or windy conditions
  • Keep clear of power lines (critical safety risk)
  • If unsure, hire a licensed installer

When to call a professional

Consider a pro installer if:

  • Multi-storey home or difficult roof access
  • Persistent signal issues
  • You want optimal digital tuning (especially for HD stability)

 

Electronic Security Specialists

Australian Security & Antennas provides a comprehensive range of electronic security installation and servicing solutions across Melbourne for both residential and commercial properties, including:

  • CCTV surveillance system installation (residential & commercial)
  • Intercom system installation (residential & commercial)
  • Alarm system installation (residential & commercial)

 

 

TV on the wall 

Hanging a TV on the wall is pretty straightforward if you plan it properly, but the main risk is getting the mounting wrong and ending up with a cracked wall or a dropped TV. The key is finding a solid wall structure, using the right bracket, and not trusting plasterboard alone unless it’s properly reinforced.

What you’ll need

  • A compatible TV wall mount bracket (fixed, tilting, or full-motion)
  • Drill + appropriate drill bits
  • Stud finder
  • Spirit level
  • Screwdriver / socket set
  • Wall anchors (only if you can’t hit studs or masonry)
  • Tape measure + pencil

Step 1: Choose the right mount

TV wall mount bracket

  • Fixed mount: Sits flat against the wall (cleanest look)
  • Tilting mount: Angles down slightly (good for higher placements)
  • Full-motion mount: Pulls out + swivels (best flexibility, most complex)

Make sure it matches your TV’s VESA pattern (the hole spacing on the back).

Step 2: Find the wall structure (this matters most)

  • Use a stud finder to locate timber or steel studs
  • In brick/concrete walls, you’ll anchor directly into masonry
  • Avoid mounting into hollow plasterboard alone unless you’re using proper heavy-duty anchors rated for the TV weight

A lot of TV failures happen here—people overestimate plasterboard strength.

Step 3: Mark and measure

  • Decide viewing height (centre of TV is usually eye level when seated)
  • Mark bracket holes
  • Double-check with a spirit level before drilling

Step 4: Drill and mount the bracket

  • Drill pilot holes into studs or masonry
  • Secure bracket tightly using appropriate screws/bolts
  • Re-check level after tightening

Step 5: Attach TV to bracket

  • Fix mounting arms to the back of the TV
  • Lift carefully (ideally 2 people for TVs over ~40 inches)
  • Hook or bolt onto the wall plate
  • Lock safety catches

Modern TVs like those from Samsung or LG Electronics often have standard VESA mounts, but always check the manual first.

Step 6: Cable management

  • Run cables behind a cover strip or in-wall conduit
  • Leave slack so the TV can tilt or swivel without strain
  • Keep power and HDMI separated if possible to reduce interference clutter

Common mistakes to avoid

  • Mounting too high (neck strain is real after 1–2 hours)
  • Using random screws that didn’t come with the bracket
  • Ignoring stud location and relying on plasterboard only
  • Not checking VESA compatibility before buying the mount
  • Mounting before confirming cable access (this one is very common)

Quick reality check

If the TV is large (55"+), or you’re unsure about wall type (especially older plaster walls in apartments), it’s often worth paying a professional installer. The cost is usually far less than replacing a dropped screen.

 

TV Points

“TV points install” usually refers to adding a TV antenna wall outlet (coaxial socket) in a room so you can plug a television directly into the home antenna system.

What installation involves

A typical install looks like this:

  • Find the existing antenna feed or splitter (often in roof space, garage, or utility cupboard)
  • Run coaxial cable from that point to the new room
  • Cut and mount a wall plate (TV point/socket) on the wall
  • Terminate the cable with a coax connector behind the plate
  • Test signal quality on the TV and tune channels if needed

When you need a new TV point

  • A room has no antenna socket
  • You’ve moved the TV to a new location
  • Older homes only have 1–2 points and need expansion
  • Renovations or extensions

DIY vs professional install (Australia)

In Melbourne and most of Australia:

  • DIY is possible if you’re comfortable with cabling and have access to the roof/splitter
  • Most people use a licensed electrician or TV antenna installer, especially for:
    • Multi-storey homes
    • Roof access work
    • Signal issues or booster installation

Typical cost (Melbourne)

  • Simple single TV point install: ~$150–$300
  • Additional points in same job: ~$80–$200 each
  • More complex jobs (long cable runs, roof work, boosters): $300–$600+

Common extras

  • Signal amplifier/booster if reception is weak
  • Replacing old coax cabling (common in older homes)
  • Wall cavity fishing (no visible conduit)

Quick check before installing

  • Do you already have a working antenna on the roof?
  • Is there an existing splitter in the house?
  • Are you adding a point in a room close to existing wiring?

If you want, tell me:

  • how many rooms you want connected, and
  • whether it’s a single-storey or double-storey home